The difference between throwing pole and sea pole. As the name suggests, the long-distance casting technique is a special fishing method of long-distance casting rod. The long-distance casting rod seems to be different from the "sea rod" we usually use, but in fact, it is different. This kind of rod was originally used for beach fishing, which is suitable for places where there are no reefs underwater on the beach, and it is also suitable for freshwater fishing. Because of its long-distance advantage, long-distance rod is favored by sea anglers, and gradually adopted by freshwater anglers in recent years.

1: The purpose of long-distance casting is to find fish hiding places or places that fish must pass through. However, due to the limitation of the length of the hand pole, it is difficult for ordinary sea pole to break through 70 meters. In many fishing grounds with large water surface, the closer to the fishway, there will be more chances to catch fish.

2: The difference between long-distance casting rod and sea rod long-distance casting rod is a kind of sea rod, which evolved according to the needs of fishing ground. Generally, the sea poles used by freshwater fishermen are about 3 meters, and some use 3.9 sea poles. Although the length has reached the requirements of long-distance casting, the tonality and design of the poles are different. In order to reduce the line resistance, the magnetic eye of the wire is generally 5, and the number of segments is 4-6 according to the length of the rod. The base length of the long-distance casting rod should be 3.9-4.5m, and the hardness (hammer load) should be No. 25-no. 40. Generally, the greater the weight of the hammer, the greater the hardness of the rod. If the mark of a long-distance throwing rod is No. 30, then the suitable throwing hammer is No. 30 (equivalent to 112 grams). The distance between the bottom handle of the long-distance casting pole and the winding wheel is long, usually 50-60 cm. In order to increase the arm of force, there is only one purpose, long-distance casting.

3: Distance and resistance if you want to reach a longer distance, you must overcome the resistance from all aspects. 1) The biggest resistance of air resistance long throw is from the friction between the main line and the air. The smaller the line diameter is, the smaller the resistance is. The long throw angler usually uses the smaller line diameter to get a longer throw distance. The influence of wind on the line should be considered when casting the pole. If there is wind, the intermittent casting should be selected when the wind stops. 2) Line resistance to choose a relatively soft fishing line, hard line memory is strong, especially on the line cup winding too long has been aging line, with a strong memory, so in order to minimize the resistance of line group, fishing line should be as thin as possible, soft, try to change every year. 3) Resistance of wire ring (magnetic eye) in order to reduce the friction between the outgoing line and the wire ring, the telecontrol pole usually has five wire rings. The inner wall of the wire ring with good quality is smooth and wear-resistant. The wire ring and tyre recognized in the market are Fuji brand. Generally, the wire ring of this brand is used for telecontrol poles above the middle end. 4) The resistance of the winding wheel (winder) the cup head of the winding wheel will form resistance by friction with the wire when it goes out. Now many manufacturers have specially designed the remote casting wheel. The cup shape is higher, the slot is shallow, the cup body is slightly tapered, the top is thin and the bottom is thick, and the edge of the cup head is designed as a slope. In short, everything is for the purpose of quickly going out and reducing resistance. In order to reduce the resistance, the cup should be as full as possible. In order to prevent disordered wire, do not turn on the reverse switch easily. When you need to pull the wire, you can loosen the release force. Generally, the model of winding wheel suitable for freshwater remote casting is 5000-8000.

4: Throw the pole skills and methods: 1) throw the wind line 1 meter, open the cup, hold the line with the index finger, hold the line at an angle of 90 degrees to the pole (to prevent disordered line), lift the pole over the top of the head, keep the left foot in front and the right foot behind, watch the front landing point, lean back, drive with leg force and waist force, throw the line with two arms, the line angle is 60 degrees, and the pole stopping angle is 45 degrees, And keep this angle until the plumb enters the water, and the plumb does not touch the ground. 2) Throw the wind line 1.5m from the side, open the cup, hold the line with the index finger, lift the pole to the right side (the cup is in the right ear), separate the feet from the front to the back, observe the landing point with eyes, raise the arm, lean back, and look up with eyes (increase the angle of leaning back). At this time, the plumb is dragging the floor (pulling inside or supporting outside), and the wind line must be as straight as possible to prevent the pole tip from winding. Inside drag: the wind line is stretched to the inside, and the plumb touches the ground, forming a V-shape with the pole body lying forward. Outside drag: the wind line is stretched to the outside, and the plumb touches the ground. 3) 360 degree throwing is a professional long-distance throwing method. In the international long-distance throwing competition, the throwing method commonly used by competitors is mainly to use the rapid rotation of the body, which is highly skilled, difficult to make, high requirements for the venue and insufficient applicability.